Exporter

Manufacturer

ACARKARDEŞLER SONDAJ MAKİNA LTD. ŞTİ.

1.MAST
Mast Load Capacity	70 tons
Mast Pipes Diameter and Thickness	4”inches- 6 mm

Dimensions of the Mast
Length:	12 meters
Rear Width:	1.50 meters
Height:	1.05 meters

2. DECK ENGINE
Single Diesel Deck Engine will be mounted on the Rig.
Deck Engine is 336 hp.
Deck Engine is Turbo Intercoole.
Engine Transmission is 90 ZF and Clutch Plate diameter is 42 cm.

3. POWERTRAIN SYSTEM
Transfer Case is with two transmissions.
Transmissions are 90 ZF and diameter of Clutch Plate is 42 cm.
Transfer Case will have 7 transfers Output.
Chains of Transfer Case are 1 ” and 4 roller.
Transfer Case is with 1 ”-quadruple sprocket
Drive Shafts are big type Total Number of Drive Shafts is 5.

4. DRAW-WORKS
Two piece – Mechanical Double Drum Draw Works will be mounted abreast (side by side) on the Rig.
Drums diameter is 580 mm.
Brake Drums diameter is 600 mm
Each Drum has 5 pcs Gear tooth Facings.
These Gear tooth Facings outer diameter is 480 mm, thickness is 16mm
And number of teeth is 75
Draw-works hook load capacity is 55 tons.

5. ROTARY TABLE
Dimensions of the Rotary table
Inner Diameter	230 mm
Rotary load capacity is 70 tons.
Rotary rotation speed (as Deck Engine rotation speed is 330 rpm):
First gear	25 rpm
Second gear	35 rpm
Third gear	60 rpm
Forth gear	90 rpm
Fifth gear	125 rpm
Sixth gear	155 rpm
Reverse gear	20 rpm

6. SWIVEL AND KELLY BAR
A. Swivel
Swivel load capacity	75 tons
Swivel Pipe diameter	3 inches
Swivel is made of Steel
B.Kelly
Kelly Bar is US-Made, 4 corners
Kelly Bar length is 8,5 meters 
Pulley blocks of Kelly bar are with 4 wheels and 8 ropes
Pulley blocks of service are with 3 wheels and 6 ropes

7. CIRCULATION SYSTEM
A. Centrifugal Pump
One piece SP3 Centrifugal Pump will be mounted on the Rig.
Centrifugal Pump water Suction Line diameter is 4inches and discharge line diameter is 3inches. Centrifugal Pump discharge pipe outlet diameter is 1.5inches
Length of  Discharge Hose is  10 meters
There will be one piece- 4inchesValve and 6 meters- 4 inches water suction hose-with Centrifugal Pump
Water Pressure Hoses of the Rig is 3 inches in diameter
and 2-wired metal pressed

8. HYDRAULIC SYSTEM
Total Number of Hydraulic Lifts on the Rig is 9.
Two Hydraulic Lifts for lifting up Rig-Mast.
Four-piece Leg-Lifts for getting fixed and lifting up theRig.
Front and rear legs of the Rig are double- legged and hydraulic lifts will be in the middle of these two legs.
Two-piece Hydraulic Lifts for sliding Rotary Table for ward and back
One Piece Hydraulic Lift fort he Hydraulic Tong Key
Volume of hydraulic pump is 105 liters
And oil pressure hoses will be 2 wired

9. ELECTRIC POWER SYSTEM
One piece 100 Kva Alternator will be on the Rig
320 Amp Welding Machine will be mounted
Total Number of Lightning Projectors is 5 and Lightning Distance is 25 meters
Control Panel will have Engine Start& Stop Button, heat and oil indicator

10. CROWN BLOCK AND DRILL-LINE SYSTEM
Crown Block diameter is 42 cm
Total Crown Block Number is 10
Lines Diameter is 20 mm and 6×36
Total Length of Lines is 300 meters

11. AUXILIARY PARTS
One piece Manual Tong + One piece Hydraulic Tong (American – Brand).
One piece Pipe-Vise.
One piece Manual Hoisting Plug.
One Piece Pipe- Slip.
One piece 8½”,12½” and 17½” Drilling Sub (Coupling Sleeve)

400 meters Water Drilling Rig  Mounted on Truck (Without Truck)

1.MAST
Mast Load Capacity	80 tons
Mast Pipes Diameter and Thickness	3”inches- 6 mm

Dimensions of theMast
Lenght:	14,5 meters
RearWidth:	1.40 meters
Height:	1.05 meters

2. DECK ENGINE
Single Diesel Deck Engine will be mounted on the Rig.
Deck Engine is 360 Hp.
Deck Engine is Turbo Intercooler.
Engine Transmission is 90 ZF and Clutch Plate diameter is 42 cm.

3. POWERTRAIN SYSTEM
Transfer Case is with two transmissions.
Transmissions are 90 ZF and diameter of Clutch Plate is 42 cm.
Transfer Case will have 7 transfer Out put.
Chains of Transfer Case are 1” and 4 roller.
Transfer Case is with 1”-quadruple sprocket
Drive Shafts are big type Total Number of Drive Shafts is 5.

4. DRAW-WORKS
Two piece – Mechanical Double Drum Draw Works will be mounted abreast (sidebyside) on the Rig.
Drums diameter is 580 mm.
Brake Drums diameter is 600 mm
Each Drum has 4 pcs Geartooth Facings.
Draw-works hook load capacity is 55 tons.
5. CIRCULATION SYSTEM
B. Mud Pump
One Piece 6x8 Mud Pump will be on theRig
Mud Pump Flow Rate is 1450 lt/min 
Mud Pump Suction Line diameter is 4 inches and discharge line diameter is 3 inches and discharge pipe outlet diameter is 1.5 inches
Length of  Discharge Hose is 10  meters
There will be one piece -4 inches Valve and 6 meters- 4 inches water suction hose- with Mud Pump

A. Centrifugal Pump
One piece SP3 Centrifugal Pump will be mounted on the Rig 
Centrifugal Pump water Suction Line diameter is 4inches and discharge line diameter is 3inches. Centrifugal Pump discharge pipe outlet diameter is 1.5inches
Length of Discharge Hose is 10 meters
There will be one piece- 4inchesValve and 6 meters- 4 inches water suction hose-with Centrifugal Pump
Water Pressure Hoses of the Rigis 3 inches in diameter
and 2-wired metal pressed
1 PCS Foam pump will added on the rig

6. ROTARY TABLE
Dimensions of the Rotary table
Inner Diameter	230 mm
MedianDiameter	600 mm
Outer Diameter	800 mm
Rotary Table Ground Clearance	160cm	220 cm (max)
Rotary Table bottom and top seals are buried forair-system
Heavy duty fabricated frame
Rotary load capacity is 50 tons.
Rotary rotation speed (as Deck Engine rotationspeed is 330 rpm):
First gear	25 rpm
Second gear	35 rpm
Third gear	60 rpm
Forth gear	90 rpm
Fifth gear	125 rpm
Sixth gear	155 rpm
Reverse gear	20 rpm

7. SWIVEL AND KELLY BAR
A. Swivel
Swivel load capacity	60 tons
Swivel Pipe diameter	3 inches
Swivel is made of Steel

B.Kelly
Kelly Bar is US-Made, 6 corners 
Kelly Bar length is 11 meters 
Pulley blocks of Kelly bar are with 3 wheels and 6 ropes
Pulley blocks of Kelly bar are with 3 wheels and 6 ropes

8. HYDRAULIC SYSTEM
Total Number of Hydraulic Lifts on the Rig is 8.
Two Hydraulic Lifts for lifting up Rig-Mast.
Four piece Leg-Lifts for getting fixed and lifting up the Rig.
Front and rear legs of the Rig are double- legged and hydraulic lifts will be in the middle of these two legs.
Two piece Hydraulic Lifts for sliding Rotary Table forward and back
Volume of hydraulic pump is 80 liters
And oil pressure hoses will be 2 wired

9. ELECTRIC POWER SYSTEM
One piece 100 KWa Alternator will be on the Rig (Turkish Brand)
320 AmpWelding Machine will be mounted (Turkish Brand)
Total Number of Lightning Projectors is 6+3 extra  Lightning Distance is 25 meters
Control Panel will have Engine Start& Stop Button, heat and oil indicator

10. CROWN BLOCK AND DRILL-LINE SYSTEM
Crown Block diameter is 32 cm
Total Crown Block Number is 10
Lines Diameter is 20 mm and 6×36
Total Length of Lines is 260 meters

11. AUXILIARY PARTS
One piece Manual Tong + Hydraulic Tong
One piece Pipe-Vise
One piece Hoisting Plug  
One Piece Pipe- Slip
One piece 8½”,12½” and 17½” Drilling Sub (Coupling Sleeve)

800 meters Water Drilling Rig  Mounted on Truck (Without Truck)

1.MAST
Mast Load Capacity	120 tons
Mast Pipes Diameter and Thickness	4”inches- 6 mm (Pipe - Type)

Dimensions of the Mast
Lenght:	15.5 meters
Rear Width:	2,75 meters
Height:	1.15 meters
Ground Clearance of Mast is 18,40 -20,30 meters
Monkey board (Balcony) will be built to the mast

2. DECK ENGINE
Double Diesel Deck Engine will be mounted on the Rig
One engine is 423 Hp and the other engine is 423 Hp 
Both Deck Engines are Turbo Inter cooler 
Engine Transmission is 151 ZF and Clutch Plate diameter is 42 cm.

3. POWERTRAIN SYSTEM
Transfer Case will be with double engine input
Transmissions are 151 ZF and diameter of Clutch Plate is 42 cm.
Transfer Case will have10 transfer Output.
Chains of Transfer Case are 1⅟4” and 4 roller.
Transfer Case is with 1⅟4”-quadruple sprocket
Drive Shafts are big type Total Number of Drive Shafts is 6.
Bearings and rubber seals for Transfer case

4. DRAW-WORKS
Two piece – Mechanical Double Drum Draw Works will be mounted abreast (side by side) on the Rig.
Drums diameter is 850 mm.
Brake Drums diameter is 900 mm
Each Drum has 4 pcs Geartooth Facings.
These Gear tooth Facing souter diameter is 715 mm, thickness is 22 mm
And number of teeth is 111
Draw-works hook load capacity is 85 tons.

5. ROTARY TABLE
Dimensions of the Rotary table
Inner Diameter	14,5”
Rotary Table Ground Clearance	160cm	300 cm (max)
Rotary Table bottom and top seals are buried for air-system
Heavy duty fabricated frame
Rotary load capacity is 80 tons.
Rotary rotation speed (as Deck Engine rotation speed is 330 rpm):
First gear	25 rpm
Second gear	35 rpm
Third gear	60 rpm
Forth gear	90 rpm
Fifth gear	125 rpm
Sixth gear	155 rpm
Reverse gear	20 rpm

6. SWIVEL AND KELLY BAR
A. Swivel
Swivel load capacity	105 tons
Swivel Pipe diameter	3 inches
Swivel is made of Steel
rubber seals for swivel

B.Kelly
Kelly Bar is US-Made, 4 corners- ORGINAL AMERICAN BRAND
Kelly Bar length is 11,5 meters 
Pulley blocks of Kelly bar are with 4 wheels and 8 ropes
Pulley blocks of service are with 4 wheels and 8 ropes

7. CIRCULATION SYSTEM
A.Mud Pump
One Piece 7,5 x10 Mud Pump will be on the Rig
Mud Pump Flow Rate is 1950 lt/min
Mud Pump Suction Line diameter is 5 inches and discharge line diameter is 3 inches and discharge pipe outlet diameter is 1,5 inches
Length of Discharge Hose is 10 meters
There will be one piece -4 inches Valve and 6 meters- 5 inches water suction hose- with Mud Pump
rubber seals for mud pump
Mud Pump will be Start / Shutdown with Air pneumatic

B. Centrifugal Pump
One piece SP3 Centrifugal Pump will be mounted on the Rig.
Centrifugal Pump water Suction Line diameter is 4inches and discharge line diameter is 3inches. Centrifugal Pump discharge pipe outlet diameter is 1.5inches
Length of Discharge Hose is 10 meters
There will be one piece- 4inchesValve and 6 meters- 4 inches water suction hose-with Centrifugal Pump
Water Pressure Hoses of the Rigis 3 inches in diameter
and 2-wired metal pressed
One Piece Foam Pump for Air-Drilling will be added on the Rig.
Centrifugal & Foam Pumps will be Start / Shutdown with Air pneumatic

8. HYDRAULIC SYSTEM
Total Number of Hydraulic Lifts on the Rig is 11.
Two Hydraulic Lifts for lifting up Rig-Mast (Telescopic)
Two Hydraulic Lifts for lifting up the Monkey Balcony
Four piece Leg-Lifts for getting fixed and lifting up theRig.
Front and rear legs of the Rig are double- legged and hydraulic lifts will be in the middle of these two legs.
Two piece Hydraulic Lifts for lift the Platform Board
Volume of hydraulic pump is 105 liters
And oil pressure hoses will be 2 wired

9. ELECTRIC POWER SYSTEM
One piece 100 Kva Alternator will be on the Rig
360 DC Welding Machine will be mounted
Total Number of Lightning Projectors is 5 and Lightning Distance is 25 meters
Control Panel will have Engine Start& Stop Button, heat and oil indicator
(Alternator & Welding ) Start / Shutdown with Air pneumatic

10. CROWN BLOCK AND DRILL-LINE SYSTEM
Crown Block diameter is 45 cm
Total Crown Block Number is 14
Lines Diameter is 20 mm and 6×36
Total Length of Lines is 400 meters
Bearings for crown block.

11. AUXILIARY PARTS
One piece Manual Tong + One piece Hydraulic Tong (American – Brand)
One piece Pipe-Vise (Hydraulic)
One piece Hoisting Plug for Air compressor
One piece Manual Hoisting Plug   
One Piece Pipe- Slip 
One piece 8½”,12½” and 17½” Drilling Sub (Coupling Sleeve) 
One piece Weight indicator will be added to the Rig
Platform Board will be added behind the Rig (300x300) cm
305 pcs combination socket & wrench set will be added extra
One piece 5 tons winch for service

1300 meters Depth Drilling Rig  Mounted on Truck (Without Truck)

1.MAST
Mast Load Capacity	80 tons
Mast Pipes Diameter and Thickness	4”inches- 6 mm

Dimensions of the Mast
Length:	14,5 meters
Rear Width:	1.80 meters
Height:	1.15 meters
Monkey board (Balcony) will be built to the mast

2. DECK ENGINE
Single Diesel Deck Engine will be mounted on the Rig.
Deck Engine is 361 Hp 
Deck Engine is Turbo Intercoole.
Engine Transmission is 90 ZF and Clutch Plate diameter is 42 cm.

3. POWERTRAIN SYSTEM
Transfer Case is with two transmissions.
Transmissions are 90 ZF and diameter of Clutch Plate is 42 cm.
Transfer Case will have 7 transfers Output.
Chains of Transfer Case are 1 ” and 4 roller.
Transfer Case is with 1 ”-quadruple sprocket
Drive Shafts are big type Total Number of Drive Shafts is 5.

4. DRAW-WORKS
Two piece – Mechanical Double Drum Draw Works will be mounted abreast (side by side) on the Rig.
Drums diameter is 580 mm.
Brake Drums diameter is 600 mm
Each Drum has 5 pcs Gear tooth Facings.
These Gear tooth Facings outer diameter is 480 mm, thickness is 16mm
And number of teeth is 75
Draw-works hook load capacity is 55 tons.

5. ROTARY TABLE
Dimensions of the Rotary table
Inner Diameter	230 mm
Rotary load capacity is 70 tons.
Rotary rotation speed (as Deck Engine rotation speed is 330 rpm):
First gear	25 rpm
Second gear	35 rpm
Third gear	60 rpm
Forth gear	90 rpm
Fifth gear	125 rpm
Sixth gear	155 rpm
Reverse gear	20 rpm
6. SWIVEL AND KELLY BAR
A. Swivel
Swivel load capacity	75 tons
Swivel Pipe diameter	3 inches
Swivel is made of Steel
B.Kelly
Kelly Bar is US-Made,  6 corneres
Kelly Bar length is 11 meters 
Pulley blocks of  Kelly bar are with 4 wheels and 8 ropes
Pulley blocks of service are with 4 wheels and 8 ropes

7. CIRCULATION SYSTEM
A.Mud Pump
One Piece 6”x8” Mud Pump will be on the Rig
Mud Pump Flow Rate is 1550 lt/min.
Mud Pump Suction Line diameter is 4 inches and discharge line diameter is 3 inches and discharge pipe outlet diameter is 1.5 inches
Length of  Discharge Hose is 10  meters
There will be one piece -5 inches Valve and 6 meters- 4 inches water suction hose- with Mud Pump

B. Centrifugal Pump
One piece SP3 Centrifugal Pump will be mounted on the Rig.
Centrifugal Pump water Suction Line diameter is 4inches and discharge line diameter is 3inches. Centrifugal Pump discharge pipe outlet diameter is 1.5inches
Length of  Discharge Hose is  10 meters
There will be one piece- 4inchesValve and 6 meters- 4 inches water suction hose-with Centrifugal Pump
Water Pressure Hoses of the Rig is 3 inches in diameter
and 2-wired metal pressed
1 PCS foam pump will be added on the Rig


8. HYDRAULIC SYSTEM
Total Number of Hydraulic Lifts on the Rig is 9.
Two Hydraulic Lifts for lifting up Rig-Mast.
Four-piece Leg-Lifts for getting fixed and lifting up theRig.
Front and rear legs of the Rig are double- legged and hydraulic lifts will be in the middle of these two legs.
Two-piece Hydraulic Lifts for sliding Rotary Table for ward and back
Volume of hydraulic pump is 105 liters
And oil pressure hoses will be 2 wired

9. ELECTRIC POWER SYSTEM
One piece 100 Kva Alternator will be on the Rig
320 Amp Welding Machine will be mounted
Total Number of Lightning Projectors is 6 and Lightning Distance is 25 meters
Control Panel will have Engine Start& Stop Button, heat and oil indicator

10. CROWN BLOCK AND DRILL-LINE SYSTEM
Crown Block diameter is 42 cm
Total Crown Block Number is 10
Lines Diameter is 20 mm and 6×36
Total Length of Lines is 300 meters

11. AUXILIARY PARTS
One piece Manual Tong + One piece Hydraulic Tong (American – Brand).
One piece Pipe-Vise Hydraulic
One piece Manual Hoisting Plug   .
One Piece Pipe- Slip.
1 Pcs weight Indicator 
One piece 8½”,12½” and 17½” Drilling Sub (Coupling Sleeve) 
Platform Board will be added behind the Rig

800 meters Water Drilling Rig  Mounted on Trailer

1.MAST
Mast Load Capacity	120 tons
Mast Pipes Diameter and Thickness	4” inches- 6 mm

Dimensions of theMast
Lenght:	15,5 meters
Rear Width:	2,45 meters
Height:	1.15 meters
Ground Clearance of Mast is 17-18 meters
Monkey board (Balcony) will be built to the mast

2. DECK ENGINE
Double Diesel Deck Engine will be mounted on the Rig
One engine is 420Hp and the other engine is 420Hp too
Both Deck Engines are Turbo Intercooler.
Engine Transmission is 151 ZF andClutch Plate diameter is 42 cm.

3. POWERTRAIN SYSTEM
Transfer Case will be with double engine input
Transmissions are 151 ZF and diameter of Clutch Plate is 42 cm.
Transfer Case will have10 transfer Output.
Chains of Transfer Case are 1⅟4” and 4 roller.
Transfer Case is with 1⅟4”-quadruple sprocket
Drive Shafts are big type Total Number of Drive Shafts is 5.

4. DRAW-WORKS
Twopiece – Mechanical Double Drum Draw Works will be mounted abreast (sidebyside) on the Rig.
Drums diameter is 850 mm.
Brake Drums diameter is 900 mm
Each Drum has 4 pcs Geartooth Facings.
These Gear tooth Facing souter diameter is 715 mm, thickness is 22 mm
And number of teeth is 111
Draw-works hook load capacity is 85 tons.

5. SWIVEL AND KELLY BAR
A. Swivel
Swivel load capacity	80 tons
Swivel Pipe diameter	3 inches
Swivel is made of Steel

B.Kelly
Kelly Bar is US-Made, 4 or 6 corners
Kelly Bar length is 11 meters 
Pulley blocks of Kelly bar are with 4 wheels and 8 ropes
Pulley blocks of Service are with 4 wheels and 8 ropes

6. ROTARY TABLE
Dimensions of the Rotary table
Inner Diameter	370 mm
Rotary Table Ground Clearance	160cm	300 cm (max)
Rotary Table bottom and top seals are buried for air-system
Heavy duty fabricated frame
Rotary load capacity is 80 tons.
Rotary rotation speed (as Deck Engine rotation speed is 330 rpm):
First gear	25 rpm
Second gear	35 rpm
Third gear	60 rpm
Forth gear	90 rpm
Fifth gear	125 rpm
Sixth gear	155 rpm
Reverse gear	35 rpm

7. CIRCULATION SYSTEM
A.Mud Pump
One Piece 7,5 x10 Mud Pump will be on the Rig
Mud Pump Flow Rate is 1950 lt/min
Mud Pump Suction Line diameter is 5 inches and discharge line diameter is 3 inches and discharge pipe outlet diameter is 1.5 inches
Length of Discharge Hose is 10 meters
There will be one piece -5 inches Valve and 6 meters- 5 inches water suction hose- with Mud Pump

B. Centrifugal Pump
One piece SP3 Centrifugal Pump will be mounted on the Rig.
Centrifugal Pump water Suction Line diameter is 4inches and discharge line diameter is 3inches. Centrifugal Pump discharge pipe outlet diameter is 1.5inches
Length of  Discharge Hose is  10 meters
There will be one piece- 4inches Valve and 6 meters- 4 inches water suction hose-with Centrifugal Pump
Water Pressure Hoses of the Rigs 3 inches in diameter
and 2-wired metal pressed
One Piece Foam Pump for Air-Drilling will be added on the Rig.

8. HYDRAULIC SYSTEM
Total Number of  Hydraulic Lifts on the Rig is 13.
Two Hydraulic Lifts for lifting up Rig-Mast. (Telescopic).
Two Hydraulic Lifts for lifting up the Monkey Balcony.
Four piece Leg-Lifts for getting fixed and lifting up the Rig.
Front and rear legs of the Rig are double- legged and hydraulic lifts will be in the middle of these two legs.
Two piece Hydraulic Lifts for sliding Rotary Table for ward and back
Two piece Hydraulic Lifts for the Platform Board + One piece Hydraulic Lifts fort he Hydraulic Tong
Volume of hydraulic pump is 105 liters
And oil pressure hoses will be 2 wired

9. ELECTRIC POWER SYSTEM
One piece 100 KW Alternator will be on the Rig
320 Amp Welding Machine will be mounted
Total Number of Lightning Projectors is 5 and Lightning Distance is 25 meters
Control Panel will have Engine Start& Stop Button, heat and oil indicator
(Alternator & Welding) Start / Shutdown with Air pneumatic

10. CROWN BLOCK AND DRILL-LINE SYSTEM
Crown Block diameter is 45 cm
Total Crown Block Number is 12
Lines Diameter is 20 mm and 6×36
Total Length of Lines is 350 meters

11. AUXILIARY PARTS
One piece Manual Tong + One piece Hydraulic Tong (American – Brand)
One piece Pipe-Vise (Hydraulic)
One piece Hoisting Plug  + One Piece Hoisting Plug for Air Compressor
One Piece Pipe- Slip
One piece 8½”,12½” and 17½” Drilling Sub (Coupling Sleeve)
Weight indicator will be added to the Rig
Platform Board will be added behind the Rig ( 300x300 ) cm
One piece 5 tons winch for service

1300-1500 meters Water Drilling Rig  Mounted on Trailer

1.MAST
Mast Load Capacity	140 tons
Mast Pipes Diameter and Thickness	4” inches- 8 mm 
Dimensions of the Mast
Lenght:	17 meters
Rear Width:	2,55 meters
Height:	1.20 meters
Ground Clearance of Mast is 19,90- 21,80 meters
Monkey board (Balcony) will be built to the mast

2. DECK ENGINE - NEW
Double Diesel Deck Engine will be mounted on the Rig
One engine is 515 Hp and the other engine is 515 Hp IVECO BRAND.
Both Deck Engines are Turbo Intercooler. 
Engine Transmission is 251 ZF and Clutch Plate diameter is 42 cm.

3. POWERTRAIN SYSTEM
Transfer Case will be with double engine input
Transmissions are 251 ZF and diameter of Clutch Plate is 45 cm.
Transfer Case will have10 transfer Output.
Chains of Transfer Case are 1⅟4” and 4 roller.
Transfer Case is with 1⅟4”-quadruple sprocket
Drive Shafts are big type Total Number of Drive Shafts is 6.

4. DRAW-WORKS
Triple Drum Draw Works (one for power train system) will be mounted rear-front on the Rig.
Drums diameter is 850 mm.
Drums has dual brake system (dual pressure plate).
Brake Drums diameter is 900 mm
Each Drum has 6 pcs Geartooth Facings (total 12 ). 
These Gear tooth Facing souter diameter is 715 mm, thickness is 22 mm
And number of teeth is 111
Draw-works hook load capacity is 125 tons.
Extra 3 Ton winch for service
5. ROTARY TABLE
Dimensions of the Rotary table – ORIGINAL AMERICAN BRAND 
Inner Diameter	17” inch
Rotary Table Ground Clearance	180cm	320 cm (max)
Rotary Table bottom and top seals are buried for air-system
Heavy duty fabricated frame
Rotary load capacity is 120 tons.
Rotary rotation speed (as Deck Engine rotation speed is 330 rpm):
First gear	25 rpm
Second gear	35 rpm
Third gear	60 rpm
Forth gear	90 rpm
Fifth gear	125 rpm
Sixth gear	155 rpm
Reverse gear	20 rpm

6. SWIVEL AND KELLY BAR
A. Swivel
Swivel load capacity	115 tons
Swivel Pipe diameter	3,5 inches
Swivel is made of Steel

B.Kelly
Kelly Bar is US-Made, 4 corners- ORIGINAL AMERICAN BRAND 135x135
Kelly Bar length is 12,5 meters 
Pulley blocks of Kelly bar are with 4 wheels and 8 ropes
Pulley blocks of service are with 4 wheels and 8 ropes

7. CIRCULATION SYSTEM
A.Mud Pump
One Piece 7,5 x10 Mud Pump will be on the Rig
Mud Pump Flow Rate is 1950 lt/min
Mud Pump Suction Line diameter is 5 inches and discharge line diameter is 3 inches and discharge pipe outlet diameter is 1,5 inches
Length of Discharge Hose is 10 meters
There will be one piece -5 inches Valve and 6 meters- 5 inches water suction hose- with Mud Pump
Mud Pump will be Start / Shutdown with Air pneumatic

B. Centrifugal Pump
One piece SP3 Centrifugal Pump will be mounted on the Rig.
Centrifugal Pump water Suction Line diameter is 4inches and discharge line diameter is 3inches. Centrifugal Pump discharge pipe outlet diameter is 1.5inches
Length of Discharge Hose is 10 meters
There will be one piece- 4inchesValve and 6 meters- 4 inches water suction hose-with Centrifugal Pump
Water Pressure Hoses of the Rigis 3 inches in diameter
and 2-wired metal pressed
One Piece Foam Pump forAir-Drilling will be added on the Rig.
Centrifugal & Foam Pumps will be Start / Shutdown with Air pneumatic

C. EXTRA MUD PUMP + ENGINE
Mounted On Iveco Engine ( ACAR PUMP 7,5x10) 
Deck Engine is 420 hp. 
Deck Engine is Iveco Brand.
ACR2 NP-250 (DUBLEX DOUBLE ACTING)
HORSE POWER: 420 HP
MAX. PRESSURE: 125 BAR, 1812 PSI
MAX. FLOW RATE: 1800 L/MIN, 533 GPM
STROKES: 10 INCH (254 mm)
Origin: Turkey

8. HYDRAULIC SYSTEM
Total Number of Hydraulic Lifts on the Rig is 10.
Two Hydraulic Lifts for lifting up Rig-Mast (Telescopic)
Two Hydraulic Lifts for lifting up the Monkey Balcony
Four piece Leg-Lifts for getting fixed and lifting up theRig.
Front and rear legs of the Rig are double- legged and hydraulic lifts will be in the middle of these two legs.
Two piece Hydraulic Lifts for lift the Platform Board
Volume of hydraulic pump is 105 liters
And oil pressure hoses will be 2 wired

9. ELECTRIC POWER SYSTEM
One piece 115 Kva Alternator will be on the Rig
500 DC Welding Machine will be mounted
Total Number of Lightning Projectors is 5 and Lightning Distance is 25 meters
Control Panel will have Engine Start& Stop Button, heat and oil indicator
(Alternator & Welding ) Start / Shutdown with Air pneumatic

10. CROWN BLOCK AND DRILL-LINE SYSTEM
Crown Block diameter is 45 cm
Total Crown Block Number is 12
Lines Diameter is 24 mm and 6×36
Total Length of Lines is 350 meters
Bearings for crown block.

11. AUXILIARY PARTS
One piece Manual Tong + One piece Hydraulic Tong (American – Brand)
One piece Pipe-Vise (Hydraulic)
One piece Hoisting Plug for Air compressor
One piece Manual Hoisting Plug   
One Piece Pipe- Slip (American – Brand)
One piece 8½”,12½” and 17½” Drilling Sub (Coupling Sleeve)
Weight indicator will be added to the Rig
Platform Board will be added behind the Rig (300x300) cm

1800-2000 meters Water Drilling Rig  Mounted on Trailer

1.TRAILER
Dimensions of 4­Axle Trailer 
Length: 16 meters
Width: 3.00 meters
Chassis Thickness is 550 ST52 (S355JR+M)
Trailer has 16 wide ­wheels and 1spare tire (all new)
Mobile ramps with 30 cm higest

2.MAST
Mast is telescobic duble mast, 
Outer mast : 17 meter long,
(Main mast) 140x140 square profile, 10 mm thickness
Inner mast : 15.50 meter long,
(Main mast) 140x140 square profile, 10 mm thickness
Mast Load Capacity	240 tons

Dimensions of the Mast
Lenght:	32 meters (from chassis to pulley blocks)
Rear Width:	2,38 meters
Ground clearance of the mast is 36 meters
Grand pully block table has 8 wheel. (wheel diameters 1000 mm)
Mast standby line will be 1,5 inches
Inner mast and mast lock system will be hydraulic system.
Monkey board (Balcony) will be built to carry 2500 meter rods.

3. DECK ENGINE – NEW BRAND
Two Diesel Deck Engine will be mounted on the Rig
Deck engine is CAT – C18 / 600 HP – 650 HP (NEW)
 in total (1300 HP)
Engine Transmissions are ALLISON (6700 Series) in total two pcs

4. POWERTRAIN SYSTEM
Transfer Case will be one input and three output
Chains of Transfer Case are 1 ½ ” and 5 roller.
The case will have 3 clutch (650 mm diameter)
Transfer Case can hold for 1500 HP. 

5. DRAW WORKS
Triple Drum Draw Works
 (one for power train system) will be mounted rear-front on theRig
Drums diameter is 1160 mm.
Drums has dual brake system (dual pressure plate).
Brake Drums diameter is 800 mm
Each Drum has baloon clutch system
Water Cooling Circulation (Hydromatic brake)
Draw-works hook load capacity is 200 tons.
Extra 7,5 Ton winch for service (Dinamicoil SE60/2)

6. ROTARY TABLE SUBSTRUCTURE TYPE
Dimensions of the Rotary table spraeted
Inner Diameter	27” 

7. SWIVEL, KELLY BAR AND PULLEY BLOCKS
A. Swivel
Swivel load capacity	200 tons
Swivel Pipe diameter	6 inches

B.Kelly
US-MADE Kelly Bar length is 12 meters and Kelly Bar width is 
130mm – 140 mm

C. Hook Block
Pulley blocks wheels diameter is 700 mm. 4 pieces, 
Hook block capacity will be 250 tons.

8. LIFTING SYSTEM (JACKS)
Total Numbe rof  double leg-Lifts on the Rig is 4.
The rig has 4 hydraulic lifts turning system.
The hight from ground to carrier will be 50 cm

9. PLATFORM AND CABIN
There will be 60 cm wide walkway all around the rig.
There will be a rod stand platform, sized 700 cm (width) X 500 cm (lenght).
The walking platforms will have railings, 
There will be an engine cabin, rod slides, ledders and two tool cabins.
Driller Cabin (Doghouse)

10. LINE (MAIN DRUM ROPES) 
Line (Main Drum Ropes) of the rigs will be 32 mm sized and 600 meter long.
Lines will be hempen and soft type.
Monkey board, hyraoulic lifts and tong will have lines ( double tong).

11. HYDRAULICS
There will be 2 telescobic mast lifts (3 outputs), 4 leg lifts, 1 inner mast lift, 2 main mast lifts, 2 tong lifts total 11 lifts. 
All lifts, control handles and installations will be new.

12. AIR SYSTEM AND INDICATORS
All systems on the rig will be air pressure system.
The rig will have 8 bar compressor.
The rig will have weight indicator, air bar indicator, mud pump pressure indicator, hydraulic bar indicator, tong power indicator and air pneumatic levers.

13. ELECTRICAL POWER  AND PAINT 
The rig will have 18 pcs ex proof lamp type lighting and 2 stop lights..
The rig will have engine indicator and engine operating time indicator.
The paint will be first class and color will be chosen according to customer’s choise
Control Panel will have Engine Start& Stop Button, heat and oil indicator

14. EQUIPMENTS
The rig will have two hydraulic tong and dummy weight.
There will be stand by line hose, kelly bujing and master bujing.

15. Separated Mud Pump (Refurbished)
Separated Mud Pump 2NP-400 With Engine
Mud pump
Acr-400 (dublex double acting) - 2np400
Horse power: 400 hp
Max. Pressure: 200 bar, 2845 psi
Max. Flow rate: 2180 l/min, 577 gpm
Strokes: 70 ds/min / Origin : romania 

16. Separated Deck Engine for Mud Pump (NEW)
Single Diesel Deck Engine will be mounted on the MUD PUMP.
Deck Engine is 570 hp.
Deck Engine is Turbo Intercooler.
The deck engine for the separated mud pump CAT C15.

2500-3000 M DEPTH DRILLING RIG & WORKOVER

Note: The machine can drill to 300 meters with 12,5 inch
It can drill to 500 meters with 8,5 inch
Machine height in walking position	
4100 mm
Width (W)	2500 mm
Length (L)	11500 mm
Mast Height (D)	9000 mm
Weight	14000 kg
Immobilization	HYDRAULIC FOOT FIXING
Diesel Engine	CUMMINS 250 KW/336 HP
Hydraulic Pump Set	LINDE / KAWASAKI
Rotary Feeding Hydraulic Pump	
LINDE
Push-Pull Feed Hydraulic Pump	
KAWASAKI
Deck Feeding Hydraulic Pump	
KAWASAKI
Rotary Hydromotor	PARKER
Push-Pull directional control valve	DANFOS PROPORTIONAL CONTROL
Deck directional control valve	WALVOIL
Electric Circuit	CURRENT + VOLTAGE PROPORTIONAL
Alternator	15 KW
Alternator Hydromotor	PARKER
Mud pump	4,5X6 MUD PUMP
Mud pump hydromotor	PARKER HYDROMOTOR
Maneuvering Crane	20 000 KG
Servise Crane	1500/2000 KG
Point-Pulling Speed	MAX 40/27,5 m/m
Pressure Line	HARDOX 500
Pressure Movement	HYDRAULIC PRESS
Pressure Force	MAX 12,5 TON
Pulling Force	MAX 27 TON
Rotary Torque	MAX 9000 Nm
Rotary Cycle	MAX 30/220 RPM
Working Pressure (regular)	400 BAR
Working Pressure (max.)	450 BAR
Pipe (Rod) Length	6100 MM
Rod Connection Thread	NC 38
Clamp	400 MM
Drilling Diameter	7,5 inch-max 26 INCH
Oil Tank	600 LT
Oil Cooler	HYDRAULIC RADIATOR AIR
Type of Cooling	AIR
Fuel Tank Capacity	400 LT.
Foam Injection Pump	95 LT./M TRIPLEX POMP
Remote Control	OPTIONAL

300-500 meters Depth Top Drive Hydraulic Drilling Rig  (Without Truck)

Note: The machine can drill to 500 meters with 12,5 inch
It can drill to 750 meters with 8,5 inch
Machine Height in Walking Position	
4400 mm
Width (W)	2620 mm
Length (L)	12750 MM
Mast Height (D)	12360 MM
Weight	22000 KG
Immobilization	HYDRAULIC FOOT FIXING
Diesel Engine	IVECO 310 KW / 420 HP
Hydraulic Pump Set	LINDE /KAWASAKI
Rotary Feeding Hydraulic Pump	
LINDE
Push-Pull Feed Hydraulic Pump	
KAWASAKI
Deck Feeding Hydraulic Pump	
KAWASAKI
Rotary Hydromotor	DANFOS
Push-Pull directional control valve	DANFOS
Deck directional control valve	WALVOIL
Electric Circuit	CURRENT PROPORTIONAL
Mud pump	6X8 MUD PUMP
Mud pump hydromotor	PARKER HYDROMOTOR
Maneuvering Crane	35 000 KG

Servise Crane	2000 KG
Point-Pulling Speed	29 m/m
Pressure Movement	HYDRAULIC PRESS
Pressure Force	MAX 18 TON
Pulling Force	MAX 34 TON
Rotary Torque	MAX 20 000 Nm
Rotary Cycle	MAX 30/180 RPM
Working Pressure (regular)	280-350 BAR
Working Pressure (max.)	400 BAR
Pipe (Rod) Length	6100 MM
Rod Connection Thread	NC 38
Clamp	600 MM
Drilling Diameter	7,5 inch-max 26 INCH
Oil Tank	700 LT
Oil Cooler	HYDRAULIC RADIATOR AIR
Type of Cooling	AIR
Fuel Tank Capacity	400 LT. OPTIONAL
Foam Injection Pump	95 LT./D TRIPLEX POMP
Remote Control	OPTIONAL

500-750 meters Depth Top Drive Hydraulic Drilling Rig  (Without Truck)

you're in correct address for rotary drilling in african soil.
we are 35 years experienced drilling rig company.
especially we are expert in sudan, ethiopia, somalia, kuwait, qatar, algeria, tunisia, nigeria.
we are a family company. 4 brothers are working in every stage of manufacturing.
so that we produce high quality rigs and we have happy customers.
especially warranty; you will have one year warranty. in the beginning if you decided to buy any rig from us when it finishes one of our brothers come to your country and tests the machine in front of you and gives training to your workers for 7-10 days. also after buying a machine in one year if you have a problem with the rig in couple of days we come to your country and fix the problem. you cannot find this service in any other company that built drilling rig. now for 4 years the service station is in sudan for faster service in every country in africa.
we are looking forward to have you here in our factory.

Sectors

Acarkardeşler Sondaj Maki̇na Ltd. Şti̇. Export Products